Here is a PDF with my interaction with Claude AI which is programed with skill to be as Research assitant. Inside the PDF you can see my blury, random noise question first, just wrote what came first. Then ask Grok to gleam the grammar mistakes and structure it as Buletpoint with clean structure and feed this as question to Claude. Then you see what the response is. Im sharing this because Im fascinated by the clarity and reasoning with this AI model, and Im sure that will help us tremendously to move the project further. It understood the Manual perfectly and brake down the loginc in clear and organized structure. Its jus very useful. Also, will add the images that Was uploded to with the first question. It really helps to understand the creative process of energy from many new perspectives.

What is improved? A small ring 3 mm thick with a 20mm diameter and 7 mm hole is added to the top of each cone to serve as a guide and create perfect alignment with the copper spikes at the exact center of the configuration. (Look the first image At the bottom, the Spiraling sections are trimmed, and this allows a flat base for better adhesion with the 3D printing Bed. Without this adjustment, I`m not sure if it's even possible to be 3D printed with FDM printer. You can download the Files from here if you want, and also a small 19.5 Degree cone is added as well, with 33.3cm height for those of you who want supper low budget option to experiment. This 19.5 Degree STL can be used as a mold for Fiber Glas or Kevlar, Carbon Fiber or other composite materials to create the cones and later use it as a base for the copper wire, which might be 0.35mm thickness. Basically, to use the same method that I created the previous cones, but smaller and with thinner wire. The Idea here is to create 2 or 3 Identical cones and see if they can transfer the power over a greater distance or can be used to activate the space-time antennas instead of using standart Tesla Transformer. The total cost for all 5 files was a bit less than 200Euro including shipping and the order is placed today. We can now see if this can actually be printed with PETG, and if yes what will be the quality. If these files are working, anyone can print them and make the cones very easily.

Here are 11 main ideas and principles in the most sonsize and organized ways, the last one will be in the comments becasue Im allowed to share only 10 images at ones #1 The ONE Divides into Two Bashar explained in “Bashar’s Lab” that the fabric of Space-Time is like two sides of the same ONE coin. This is what creates Time Dilation: the faster you move in Space, the slower time passes. You can see the diagram he uses to illustrate this interconnectivity and symmetry between Space and Time. The idea is that Existence is whole and hermetic because nonexistence, by definition, doesn’t exist. Therefore, there is nothing outside that is separated from, or can restrict or confine, Existence. Because of this fact, ALL creation can happen ONLY WITHIN Existence. For creation to occur, the ONE (the WHOLE) must split into at least two opposing or polarized ideas — Yin-Yang, Positive-Negative, etc. This is what allows reflection, interaction, experience, and in general consciousness to exist at all. But in the moment of the split, a fulcrum point is immediately created. This is the nexus point or place of perfect balance between the polarities, where the predominant aspect of the polarity is melted into agreement and harmony (peace in motion). These ideas are perfectly illustrated by Lao Tzu in the Tao Te Ching: “The Tao gives birth to One. One gives birth to Two. Two gives birth to Three. Three gives birth to all things.” The idea of connected polarity with a fulcrum point of balance creates the fractal, holographic, tetrahedral, Sierpiński gasket structure which is the underlying template of all Matter (Physical Reality). Look at the video. The whole nature of Infinite Existence can be illustrated as a circle (a line without beginning or end) projected into a 2D finite dimension. The first split happens when a center point is defined. Now we have center and periphery, small and big, contraction toward infinite potential and expansion toward infinite expression. Thus we have Vesica Piscis, Flower of Life, and so on, until the WHOLE EXISTENCE is divided into a corpuscular field without empty space, arranged in harmonic octaves.

Just placed the order for the Fibonacci spirals on https://jlcpcb.com/ you can download it from here and also see what Options I chose when placing the order. The total cost is 203 Euro including delivery and VAT for 5 pieces. I hope this call allows us to print the Fibonacci spirals (Flash Matrix) easily, without the need to assemble it with polycarbonate and copper wire and soldering it manually, which is pretty hard and takes time, and is more expensive per piece. Notice that up to now I was using 1mm copper magnet wire but now in the PCB we are using 1 oz copper thickness: 35 µm (1.4 mil). This seems way tinner but it is external and is not coil, because of that we can run almost 4 amperes, which is way more than we actually need. (1 mm wide, 1 oz copper trace (external layer, 10°C rise): ~3–4 A. Most IPC-2221 based sources give ~3.5–4 A). The PCB option is also 1.6mm thick Material Type: S1000H TG155 instead of 9-10 mm policarbonate used so far, this will reduce the distance between the copper hemispheres and increase the capacitance to some degree. If you decide to place an order for yourself, you need to choose Surface Finish: ENIG, which will allow you to choose copper edging that is necessary to make the inner and outer rings, where both sets of the spirals are connected (see the images attached) If some of you manage to create the 30 cm Copper hemispheres, I can send him one of these PCBs because there are 5pc and I might not be able to use them all.

https://www.youtube.com/watch?v=i2DoBy3TlGA